표제지
국문 요약
Abstract
목차
기호 설명 14
하첨자 15
제1장 서론 16
1.1. 연구의 배경 및 목적 16
1.2. 연구의 범위 및 방법 19
(1) 건물에서의 압력분포 이해를 위한 예비적 고찰 19
(2) 고층건물에서 압력분포 해석을 위한 중성대 위치 특성 분석 19
(3) 엘리베이터 샤프트 계획에 따른 중성대 위치 예측 방법 개발 20
(4) 중성대 위치 예측을 적용한 고층건물의 압력분포 평가 20
제2장 건물에서의 압력분포 해석 22
2.1. 건물에서의 압력분포에 대한 이론적 고찰 22
2.1.1. 건물에서 압력차가 미치는 영향 22
2.1.2. 건물에서의 압력차 발생 원인 27
2.2. 고층건물에서의 압력분포 해석에 관한 기존 연구 고찰 32
2.2.1. 압력분포 및 공기유동 분석 방법 32
2.2.2. 압력분포에 영향을 미치는 인자 36
2.3. 소결 42
제3장 엘리베이터 샤프트 중성대 위치 특성 44
3.1. 중성대 위치에 영향을 미치는 주요 인자 44
3.1.1. 건물의 누기분포 45
3.1.2. 엘리베이터 샤프트 수직 계획 47
3.2. 중성대 위치 예측을 위한 공기유동량 계산 방법 50
3.2.1. 엘리베이터 샤프트에서의 공기유동량 50
3.2.2. 공기유동량 산정을 위한 주요 변수 도출 54
3.3. 주요 변수에 따른 중성대 위치 평가 60
3.3.1. 압력분포 측정을 통한 주요 변수 평가 60
3.3.2. 사례 연구를 통한 주요 변수 평가 68
3.4. 소결 72
제4장 엘리베이터 샤프트 중성대 위치 예측 방법 74
4.1. 중성대 위치 예측 모델 개발 74
4.1.1. 중성대 위치 예측 모델 75
4.1.2. 중성대 위치 예측 모델 적용 범위 79
4.2. 중성대 위치 예측 방법 검증 84
4.2.1. 고층건물 엘리베이터 샤프트의 중성대 예측 84
4.2.2. 중성대 예측 모델 검증 결과 88
4.4. 소결 92
제5장 고층건물에서의 중성대 예측 기반 압력분포 평가 94
5.1. 압력분포 평가 개요 94
(1) 압력분포 평가 실내외 조건 95
(2) 압력분포 평가 모델 96
5.2. 고층건물 압력분포 평가 97
5.2.1. 엘리베이터 샤프트 계획에 따른 압력분포 97
5.2.2. 외피 입면 계획에 따른 압력분포 102
5.3. 소결 104
제6장 결론 106
참고문헌 110
Table 3.1. Elevator shaft vertical zoning type 48
Table 3.2. Airtightness data to normalized flow coefficient (n=0.62) 56
Table 3.3. Input parameters for prediction of NPL locations 59
Table 3.4. Building summary of case buildings 61
Table 3.5. Specification of instruments for measuring pressure distributions 62
Table 3.6. NPL locations of case buildings based on measurements 63
Table 3.7. Parameters of the model building 68
Table 3.8. Simulation cases 69
Table 3.9. NPL location based on simulation cases 70
Table 4.1. Envelope elevation plan types 80
Table 4.2. Elevator shaft vertical plan types 82
Table 4.3. Summary of Buildings 85
Table 4.4. Input parameters for predicting NPL locations within Building F 85
Table 4.5. Results of NPL locations for measurement and prediction 90
Table 5.1. Indoor and outdoor conditions for evaluating pressure distributions 95
Table 5.2. Model building summary 96
Table 5.3. Evaluation case (Case I) 98
Table 5.4. Evaluation case (Case II) 100
Table 5.5. Evaluation case (Case III) 102
Table 5.6. NPL location according to the elevator service zone (Case III)[내용없음] 12
Table 5.7. Criteria of stack-induced pressure difference (△Ti-₀=30K)[이미지참조][내용없음] 12
Fig. 1.1. Flow chart for this study 21
Fig. 2.1. The range of pressure differences that cause problems with doors in buildings 26
Fig. 2.2. Airflow due to stack effect and reverse stack effect 27
Fig. 2.3. Superposition between driving forces for pressure difference in a building 31
Fig. 2.4. Annual average proportion of total pressure difference attributable to each of the driving forces at the top of a building for various building heights in Vancouver 31
Fig. 2.5. Multi-zone network airflow analysis 35
Fig. 2.6. Pressure profiles according to outdoor temperatures 38
Fig. 2.7. Pressure profiles according to shaft heights 39
Fig. 2.8. Pressure profiles according to location of NPL 41
Fig. 3.1. Airflow with simplified single-zone shaft 46
Fig. 3.2. NPL Locations of high-rise buildings based on measurements and simulations 48
Fig. 3.3. Quantifying envelope elevation plans 56
Fig. 3.4. Quantifying elevator shaft vertical plans 57
Fig. 3.5. Pressure distribution profile for Building F 63
Fig. 3.6. NPL location of multi-zone shaft 64
Fig. 3.7. NPL location according to floor plan (a), and floor plans of Building E (b) and Building F (c) 66
Fig. 3.8. NPL locations according to shaft zoning plan 67
Fig. 3.9. NPL location based on simulation cases 71
Fig. 4.1. Flow chart of NPL prediction model 78
Fig. 4.2. Building scope for NPL prediction model of this study 83
Fig. 4.3. Results of mass flow calculations for predicting NPL locations 87
Fig. 4.4. Pressure distribution by measurement and prediction of Building F 89
Fig. 4.5. Results of pressure distributions for measurement and prediction 91
Fig. 5.1. Pressure distributions for model building with Case I 99
Fig. 5.2. Pressure distributions for model building with Case II 101
Fig. 5.3. Pressure distributions for model building with Case III 103